V545 24-channel VME synchro/LVDT simulation/acquisition module

Synchro/LVDT/Acquisition Module - V545
  • 24 transformer-isolated AC sinewave generator/acquisition channels
  • Generalized ADC-DAC-DSP architecture
  • Programmable functions include:
    • LVDT/RVDT acquisition, with internal or external excitation
    • LVDT/RVDT simulation, with internal or external excitation
    • Synchro/resolver acquisition, with internal or external excitation
    • Synchro/resolver simulation, with internal or external excitation
    • Poly-phase sine wave generation from 250 Hz to 20 KHz
    • True RMS voltage measurement
    • Synchronous detection
    • Frequency measurement
  • Realtime voltage and frequency measurement, all signals in all modes
  • 16 bit ADC and DAC resolution
  • Internal ARM9 CPU performs macro functions
  • Generalized function block capability
  • Clearly labeled dipswitches set VME address; no jumpers, headers, or trimpots
Request a QuoteRequest a Quote
Change View: 1 2 3 4

The V545 is a generalized- DSP-based sinewave processor intended for both simulation and acquisition of LVDTs, RVDTs, synchros, and resolvers. 24 generalized, isolated channels are provided. Each channel can be a signal source or a measurement input. Users can program any desired relationship between input and output channels, allowing simulation and measurement of a wide range of inductive transducers, using internal or external excitation.

Per-channel features include true RMS AC measurement, frequency measurement, programmable phase shift, and a versatile phase-sensitive detector.

Plugin transformers allow optional voltage input/output ranges. Software transformer ID is provided.

FUNCTION 24-channel LVDT/synchro simulator
DEVICE TYPE 16-bit VME register-based slave: A24:A16:D16;
Implements 1024 16-bit registers at switch selectable addresses in the VME 16 or 24 bit addressing spaces
I/O CHANNELS 24, transformer isolated, programmable input/output
Nominal 100 ohm output impedance with 1:1 transformers
RANGES ± 10.24 volts peak using 1:1 transformers
± 54.27 volts peak using 5.3:1 transformers
RESOLUTION 16 bits
SAMPLE RATE 250 ksps/channel
FREQUENCY RANGE 250 Hz to 20 KHz
OPERATING TEMPERATURE 0 to 60°C; extended MIL/COTS ranges available
CALIBRATION INTERVAL Two years
POWER Standard VME supplies :
+5 volts, 500 mA max
+12 volts, 2 A max
-12 volts, 2 A max
CONNECTORS Two female D25 connectors
One female D9 connector
INDICATORS LEDs indicate VME access, CPU activity, error conditions
Additional LED is user programmable
PACKAGING 6U single-wide VME module
CONFORMANCE ANSI/VITA 1-1994 (R2002) VMEbus spec; does not support byte writes
VOLTAGE GENERATION ACCURACY ± 0.50% full scale at 300 Hz to 500 Hz
RMS VOLTAGE MEASUREMENT ACCURACY ± 1% full scale at 300 Hz to 500 Hz
FREQUENCY MEASUREMENT ACCURACY 0.05%
FREQUENCY GENERATION ACCURACY 0.05%
SYNCHRO/RESOLVER ACQUISITION ACCURACY ± 0.2 degrees at 300 Hz to 500 Hz, with dash-6 transformers
SYNCHRO/RESOLVER SIMULATION ACCURACY ± 0.2 degrees at 300 Hz to 500 Hz, with dash-6 transformers
LOGIC I/O INPUTS Four TTL/CMOS/contact inputs on D9 connector
Pullup 1k-Ohm to 3.3V 0/5V Max
LOGIC I/O OUTPUTS Two open-drain outputs on D9 connector
100mA / 24V / 0.35W max

PDF Block Diagram: V545 synchro/LVDT simulation/acquisition module

PDF Datasheet: V545 synchro/LVDT simulation/acquisition module

PDF Manual: V545 synchro/LVDT simulation/acquisition module

V545-1: 24-channel VME synchro/LVDT simulation/acquisition module with 1:1 transformers

V545-4: 24-channel VME synchro/LVDT simulation/acquisition module with 3.7:1 transformers

V545-6: 24-channel VME synchro/LVDT simulation/acquisition module with 5.3:1 transformers

Additional transformers can be purchased to replace supplied transformers. Factory recalibration is recommended if transformers are replaced.

V548-1: small signal 1:1 730MH plugin transformer

V548-6: small signal 5.3:1 750MH plugin transformer